Jan 22, 2020 Symptom: To be able to SSH: a) We generate RSA keys first, however this fails with: ASR1K(config)#crypto key generate rsa modulus 2048 The name for the keys will be: asr1k.cisco.com% The key modulus size is 2048 bits% Generating 2048 bit RSA keys, keys will be non-exportable. Router(config)# crypto key generate rsa general-keys The name for the keys will be: myrouter.example.com Choose the size of the key modulus in the range of 360 to 2048 for your General Purpose Keys. Choosing a key modulus greater than 512 may take a few minutes. Get an access switch that gets you ready for 802.11ac Wave 2 and other new technologies that are here today, or coming at you tomorrow. Stackable Catalyst 3850 Series multigigabit and 10-Gbps network switches give you wired and wireless together so you can scale up and protect your investments. Feb 19, 2020 Cisco Bug: CSCvm52265 - the standby is forced to restart. When executes the command 'crypto key generate ec keysize 384'. I did a little research and found out that if I removed the rsa key by using this command ' crypto key zeroize rsa' and then added the 'crypto key generate rsa generate-keys modulus 1024, then that would work. Any thoughts? No service pad. No service password-encryption. Hostname Sales-SW-ACC2. Ip domain name my.company.come.
Are you aware of any inbound ACLs applied on the VTY lines? Maybe do a show access-list, show ip interface and show run commands to check if an ACL is blocking access on the terminal lines.
Generate A Rsa Crypto Key
If its not an ACL issue, make sure you configured 'login local' on your VTY lines to make use of the local database when connecting in
Check also that you have not disabled SSH access into your VTY lines using the transport command.
Make sure 'transport input ssh telnet' or 'transport input telnet ssh' has been configured
Failing all that it could be an exec-timeout issue, maybe that has been set to low and its automatically logging you out, although this is more unlikely based on your report.
Q: I have a Cisco switch in my network, which I can access by hooking up a console cable directly to the device. I like to access the switch remotely using SSH. How can I enable ssh on my Cisco 3750 Catalyst Switch? A: By default, when you configure a Cisco device, you have to use the console cable and connect directly to the system to access it. Follow the steps mentioned below, which will enable SSH access to your Cisco devices. Once you enable SSH, you can access it remotely using PuTTY or any other SSH client.
1. Setup Management IP
First, make sure you have performed basic network configurations on your switch. For example, assign default gateway, assign management ip-address, etc. If this is already done, skip to the next step.
Generate Crypto Key Cisco 3850 Software
In the following example, the management ip address is set as 192.168.101.2 in the 101 VLAN. The default gateway points to the firewall, which is 192.168.101.1
Crypto Key Generate Rsa Cisco 3850
2. Set hostname and domain-name
Next, make sure the switch has a hostname and domain-name set properly.
3. Generate the RSA Keys
The switch or router should have RSA keys that it will use during the SSH process. So, generate these using crypto command as shown below.
Also, if you are running on an older Cisco IOS image, it is highly recommended that you upgrade to latest Cisco IOS.
4. Setup the Line VTY configurations
Setup the following line vty configuration parameters, where input transport is set to SSH. Set the login to local, and password to 7.
If you have not set the console line yet, set it to the following values.
5. Create the username password
If you don’t have an username created already, do it as shown below.
Note: If you don’t have the enable password setup properly, do it now.
Make sure the password-encryption service is turned-on, which will encrypt the password, and when you do “sh run”, you’ll seee only the encrypted password and not clear-text password.
5. Verify SSH access
From the switch, if you do ‘sh ip ssh’, it will confirm that the SSH is enabled on this cisco device.
After the above configurations, login from a remote machine to verify that you can ssh to this cisco switch.
In this example, 192.168.101.2 is the management ip-address of the switch.
> Add your comment
If you enjoyed this article, you might also like..
Crypto Key Generate Rsa Command
Next post: How to Backup Oracle Database using RMAN (with Examples)
Generate Rsa Crypto Key Cisco
Previous post: How to Use C++ Single and Multiple Inheritance with an Example